6.0mm Portable Videoscope with Integrated 7-Inch Daylight Monitor

Product Overview

The Sugia OmniScope E4 is a field-optimized all-in-one videoscope system designed for NDT inspection crews operating in environments where bench space is unavailable and setup time must be minimized. The entire system — 7.0-inch monitor, probe interface module, cable-management spool, and accessory storage — integrates into a single IP65-rated Peli-style carry case with a total deployed weight of 6.8 kg.

The 7.0-inch IPS LCD monitor achieves 1000 cd/m² sustained brightness, making it readable in direct tropical sunlight without a viewing hood. The capacitive touchscreen supports glove-compatible operation (tested with EN 388 mechanical-protection gloves up to 1.2 mm leather thickness). The probe interface module uses a military-spec (MIL-DTL-38999 Series III) circular connector for the probe-to-console link, rated for 5000 mate/demate cycles.

The 5.0 m insertion tube is tension-rated to 45 kg axial pull, permitting retrieval from deep vertical risers without leaving residual probe segments in the inspection volume. The system runs from a 95 Wh Li-ion pack providing 6 hours of continuous inspection with the monitor at 80% brightness. Dual SDHC card slots enable simultaneous redundant recording for critical inspection documentation where data loss is not acceptable.

Key Engineering Features

• 1000-nit Daylight Monitor: 7.0-inch IPS LCD with optically bonded cover glass (no air gap); anti-reflective coating reduces specular reflection to below 1.5% at 550 nm.
• Glove-Compatible Touchscreen: Projected-capacitive touch with adjustable sensitivity; validated with EN 388 leather, nitrile, and latex gloves up to 1.2 mm thickness.
• 5.0 m Tension-Rated Insertion Tube: 45 kg axial pull rating; tungsten/Dacron hybrid braid with laser-etched depth markings at 500 mm intervals from the distal tip.
• Dual Redundant Recording: Two independent SDHC card slots configurable for either simultaneous mirror recording or sequential overflow; both support UHS-I U3 cards up to 256 GB.
• Rugged Carry-Case Integration: IP65-rated (dust-tight, water-jet resistant) polymer case with pre-cut foam insert; system operable while nested in the case with the lid open.

Technical Specifications

Parameter	Value
Probe Outer Diameter	6.0 mm
Insertion Tube Length	5.0 m
Articulation	2-way (Up/Down), 180° each direction
Probe Connector	MIL-DTL-38999 Series III circular
Image Sensor	1/6-inch Color CMOS
Effective Pixels	1280 × 720 (1.0 Megapixel)
Frame Rate	30 fps
Field of View	80° diagonal
Depth of Field	15 mm – ∞
Illumination	White LED, 4-stage
Monitor	7.0-inch IPS LCD, 1280 × 800, 1000 cd/m²
Touchscreen	Projected capacitive, glove-compatible
Storage	2× SDHC UHS-I U3 slots, up to 256 GB each
Video Output	Full-size HDMI Type A, 1080p upscaled
USB	2× USB 3.0 Type-A for external storage/peripherals
Battery	14.8 V Li-ion, 95 Wh, ~6 h runtime
AC Power	100–240 V, 50/60 Hz via external PSU
Ingress Protection	Probe tip IP67, console IP65 (case-closed) / IP54 (case-open)
Operating Temperature	-20 °C to +55 °C
System Weight	6.8 kg (complete in carry case)

Target Applications

• Oil & Gas Field NDT: Remote pipeline internal corrosion surveys at wellhead gathering stations, tank-floor underside inspection through access ports, flow-line blockage assessment.
• Power Generation: Boiler tube internal oxide-scale documentation during scheduled outages, steam-turbine casing internal visual inspection, condenser tube inlet-end erosion surveys.
• Civil Infrastructure: Bridge box-girder internal inspection through drainage access ports, post-tensioning duct void detection surveys, water-main internal corrosion mapping.
• Mining: Conveyor head-pulley bearing housing inspection, crusher mainframe internal wear-plate condition assessment, dragline boom chord internal corrosion surveys.